Welcome to official website, Beijing Huawei Guochuang Electronic Technology Co., Ltd.!
PHONE: +86 15931673319
Hot keywords:
Location: Home >>Technology sharing

Technology sharing

PHONE +86 15931673319

Compact and Efficient BGA Pick-and-Place Machine with 44 Feeder Locations

author: click::155 Publication time:2023-05-06

The operation process of the patch machine

The operation process of a pick-and-place machine generally consists of the following steps: 1. Preparing the Machine Before starting the pick-and-place process, the machine needs to be set up and calibrated to ensure that it can accurately pick and place components. This includes checking the alignment of the feeders, verifying the accuracy of the placement head, and ensuring that any necessary software updates or configurations have been made. 2. Loading the Components The next step is to load the components onto the feeders in the proper order and orientation. This is usually done by hand, and care must be taken to ensure that each component is loaded correctly and securely. 3. Creating the Placement Program Once the components are loaded, the placement program must be created or selected. This program will tell the machine which components to pick up and where to place them on the board. The program can be created using specialized software or by manually entering the coordinates and other placement parameters. 4. Starting the Placement Process With the machine set up and the placement program loaded, the pick-and-place process can begin. The machine will automatically pick up each component, verify its orientation and placement, and then place it on the board according to the program. 5. Verifying the Placement After all the components have been placed, the machine will usually perform a final verification step to check for any missed or misaligned components. Any errors can be corrected manually before the board is sent for reflow. Overall, the pick-and-place process is a key step in the PCB assembly process, and requires careful setup, programming, and verification to ensure that the finished product is of high quality and reliability.

This is the answer to the  The operation process of the patch machine question. Thank you for your attention to Beijing Huawei Guochuang Electronic Technology Co., LTD., we are a high quality SMT equipment supplier, can undertake OEM,ODM, source manufacturers reliable, we are looking for a global agent, our contact information: 15010550359 zhai 15931673319 liu.












Products Description
                                                                                          Specification
Number of feeders
50
Number of IC tray
6
Number of cameras
6
Number of heads
4
Average power
400w
Positioning precision
0.01mm
The buffer range of suction nozzle
4.5mm
Power supply
220V, 50/60Hz
Compressed air
0.5-0.6Mpa
Drive motor
Panasonic servo motor
Vacuum source of suction nozzle
high-speed on-off vacuum generator with vacuum breaker
Maximum circuit board area
600X455mm
Maximum travel scope in Z axis
20mm
Tape feeder
8, 12, 16, 24mm and vibration suction (mounting pipe chip)
Maximum mounting speed
7000Pcs/H
Average mounting speed of actual mounting resistance
8000Pcs/H
XYZ drive guide rail
TBI high-precision reloading linear guide rail
Motion drive system
Panasonic high-speed DSP drive
Operating system
full-automatic chip mounter operating system independentlydeveloped by Huawei Guochuang based on Windows
operating systemand it supports windows xp
win7 operating system
Element angle
0-360°, synchronous rotation during movement
X/Y operation mode
intelligent curve of the linear acceleration and deceleration linkage
MARK point positioning
full-automatic (the MARK point can be adjust at will)
Intelligent alarm
automatic correction, automatic filling, feeding shortage alarm
Plate entering mode
automatic connection from left to right in single sectionsautomatic PCB transfer positioning. /plunger positioning

manual plate feeding.
Visual display
17-inch industrial control display, 4:3, resolution: 1280 x1024
Number of recognition cameras
One Mark recognition camera, four quick-recognition cameras and one precise-recognition camera
Adaptive mounting scope
Adaptive to 0201, 0402, 0603, 0805, 1206, diode, audion, SOT, QFPwithin 40*40mm and the pin distance ≥0.3mm

(0.5mm center distance) and BGA
Product weight
280KG
Dimension
900X1140X1340mm

SMT pick and place machine 7000pcs/h hwt444f High speed intelligent stability high three days delivery of wooden boxes NO1


【相关推荐】